Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-28-2007, 10:06 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Bad news. The CTC38 has a bad flyback. I powered it up and the HOT runs hot and the flyback has a burnt smell as well as old wax drippings. I just left it on long enough to see what would happen. At first, the CRT checked almost dead. About 10 minutes cooking on 8 volts solved that. When I change the fly, I know I'll need to check for a proper horizontal drive signal and monitor the HOT cathode current. Is there anything else I should do to prevent possible problems? I don't know when I'll get around to fixing it. I need to fix what I've already got torn apart. But, I'm sure it's worth messing with since metal table model color tube sets seem to be rare. I didn't find that many back in the '90's when tube sets were still common.

The Sony somewhat plays. I'm sure some cleaning and adjustment will help. The GTE Philco B&W plays but the CRT is weak and it has vertical sweep issues.

Oh yes, I was going through the record compartment in the combo and found the original instruction book. The instructions on the Sony were also there. I think mine has the tube output; but, I'll double check to make sure.
Reply With Quote
  #2  
Old 11-28-2007, 10:35 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by radiotvnut View Post
Bad news. The CTC38 has a bad flyback. I powered it up and the HOT runs hot and the flyback has a burnt smell as well as old wax drippings. I just left it on long enough to see what would happen. At first, the CRT checked almost dead. About 10 minutes cooking on 8 volts solved that. When I change the fly, I know I'll need to check for a proper horizontal drive signal and monitor the HOT cathode current. Is there anything else I should do to prevent possible problems? I don't know when I'll get around to fixing it. I need to fix what I've already got torn apart. But, I'm sure it's worth messing with since metal table model color tube sets seem to be rare. I didn't find that many back in the '90's when tube sets were still common.
Two things - you're now looking for a Thordarson FLY-312 or RCA part number 119834 IIRC. There's a 119834 on eBay right now (no, not me, and I don't know/can't vouch for the seller). When you do install the new flyback, crank that efficiency coil for the proper (low) cathode current. A 0-250 mA meter (I use an analog one, bypassed with a .22uF cap) with clip leads works fine. When you finish, put a pigtail 500 mA fuse in the cathode circuit. It'll blow before the new fly cooks.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #3  
Old 11-28-2007, 11:30 PM
Chad Hauris's Avatar
Chad Hauris Chad Hauris is offline
VideoKarma Member
 
Join Date: May 2003
Location: West Texas
Posts: 2,085
I wonder if the flyback is completely bad in this case or just has been overloaded but still has a chance...On a CTC-16 and CTC-38 both had power supply or bad solder joint problems which caused no voltage to the horizontal oscillator. This overloaded and destroyed the 6JE6 tubes but repairing the oscillator power supply and replacing the output tube brought back proper operation.

If possible though a new flyback is the best solution along with a cathode fuse and current adjustment...have had a flyback fire in a CTC-31 which completely destroyed the flyback and HV tube socket. Don't know if this was an arcing problem, just bad flyback or output tube overload. The portable sets had either a circuit breaker in the horiz output cathode, a thermal fuse on the HO tube or both but for some reason the consoles/metal table top models never had this protection.

The easiest check for oscillator operation is to measure the negative grid voltage on the horizontal output tube. No voltage or weak voltage indicates poor or no oscillator operation.

Also I have had problems in the 6BK4 circuits cause problems in Magnavox sets where the flyback was overheating.

I have put in a fuse clip in the horizontal output cathode circuit and first put in a 6 volt fuse lamp to set the efficiency coil (minimum brightness on the lamp) then replaced the lamp with a 300 ma fuse.
__________________
Chad Hauris
http://www.youtube.com/user/retrochad

Last edited by Chad Hauris; 11-28-2007 at 11:34 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:50 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.