Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-25-2007, 09:06 PM
rcaman's Avatar
rcaman rcaman is offline
VideoKarma Member
 
Join Date: Nov 2002
Location: mississippi
Posts: 753
hi again, youre gonna have to put some grunt into removing those wires. just jet you a pair of pliers and yank them out. there not like most that you have to push in and turn to remove. and when you install the new splitter you can feel when the wire seats back in the new splitter. steve
Reply With Quote
  #2  
Old 11-25-2007, 09:09 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by rcaman View Post
hi again, youre gonna have to put some grunt into removing those wires. just jet you a pair of pliers and yank them out. there not like most that you have to push in and turn to remove. and when you install the new splitter you can feel when the wire seats back in the new splitter. steve
So, will I see a bare wire end, or a connector, or what? And I can just push the leads into the new splitter and that's it? Sounds easier than I expected!
EDIT: I was able to remove the splitter. The bare cable ends look like needles. I marked each lead with a Sharpie so I wouldn't mix them up, just in case.

Also, is it this resistor

http://www.tritronicsinc.com/storefr...79&itm_index=5

and which of these three choices should I go with?

http://www.tritronicsinc.com/storefr...68&itm_index=0
http://www.tritronicsinc.com/storefr...23&itm_index=1
http://www.tritronicsinc.com/storefr...73&itm_index=2

Also also, after I was told to look for R14718 and 719 to be bad, I looked and found 718 blown. 719 looks good still, I'll check it with the trusty DMM.
EDIT: R14719 is still intact. Oddly, 718 reads as still closed, but because it's burnt. I'm replacing it anyway. It sure as heck is a good thing 719 is good, because Tritronics discontinued them!
__________________
Sony Trinitron Fan
Reply With Quote
  #3  
Old 11-26-2007, 09:38 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
I'm going to go ahead and purchase one of their not in box original RCA dividers and the two resistors. If there is a reason I should go with the NIB one, let me know.
__________________
Sony Trinitron Fan
Reply With Quote
  #4  
Old 11-26-2007, 09:49 PM
rcaman's Avatar
rcaman rcaman is offline
VideoKarma Member
 
Join Date: Nov 2002
Location: mississippi
Posts: 753
it will come back to bite you in the butt. dont buy a generic splitter. that thing has 30000 volts comming and going out of it. the cheap ones wont hold up as long. steve
Reply With Quote
  #5  
Old 11-26-2007, 11:07 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by rcaman View Post
it will come back to bite you in the butt. dont buy a generic splitter. that thing has 30000 volts comming and going out of it. the cheap ones wont hold up as long. steve
So this one would be better:

http://www.tritronicsinc.com/storefr...68&itm_index=0
__________________
Sony Trinitron Fan
Reply With Quote
Audiokarma
  #6  
Old 11-27-2007, 09:47 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Just ordered the parts

I went with the original RCA divider ($50.85). Odd, the website asked me for a 'PO Number', which I don't know what is, so I just put N/A and it worked.

For me, the hardest part of this repair will be removing the old resistors and soldering in the new ones. I've never soldered onto a board before.
__________________
Sony Trinitron Fan
Reply With Quote
  #7  
Old 12-03-2007, 04:24 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
OK, the parts got here today. (all correct) I installed the new HV block no problem, but I've never done any small-scale soldering, so I'll need some tips on putting in the new resistors. (and removing the old ones) Also, I need to actually dig out my iron. Will I have to remove the board from the set to get at the bottom of it for any reason? Another big question is, if I turn on the set after replacing only the HV divider, will I fudge something up?
__________________
Sony Trinitron Fan
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:21 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.