Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-21-2007, 04:54 PM
Kiwick's Avatar
Kiwick Kiwick is offline
slave to 3 equines
 
Join Date: Mar 2007
Location: Italy
Posts: 448
Quote:
Originally Posted by Carmine View Post
As was mentioned earlier, the extra difficulties with convergence and pincushion presented by a rectangular tube were the reasons the first color sets were round, not an inability to blow a rectangular glass funnel.
I think a rectangular screen's surface is "spherical" just like a round screen's one... the only real difference is the shape... early rectangulars also had more or less the same curvature radius as roundies...

actually, one could say that a 21 inch rectangular screen is just a cut out section of a larger 21 inch round screen

i don't think the difficulty into making a rectangular screen is a matter of pincushion corrections, it's more likely a matter of easier shadowmask and phosphor dot screen construction...

The real challenge with pincushion correction and convergence came out with 110 degree color CRTs, earlier 90 or 70 degree tubes were much easier to drive... and for this very reason many late cheap sets are going back to 90 degree CRTs...
Reply With Quote
  #2  
Old 10-21-2007, 08:59 PM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Quote:
Originally Posted by Kiwick View Post
I think a rectangular screen's surface is "spherical" just like a round screen's one... the only real difference is the shape... ..
True in part, but there are a whole bunch of considerations -
Corner convergence;
Bulb strength;
Corner purity - which is related to brightness gradation:
To make obtaining purity easier, the shadow mask holes (or equivalently, the black matrix holes) were made smaller towards the edges. This was done so strongly on some rectangular designs that people complained that there was a bright area in the center of the picture (this was not a sharp-edged area, just the gradual variation from center to edge). Due to the lack of low-frequency response in the human visual system, you can get away with some of this, especially when the picture is viewed up close - but from far away it's more noticeable.

Later tubes were designed with flatter faces, making all the problems more difficult.
By that time, stripe screens had replaced dot screens, allowing self-converging yoke designs. Since vertical beam angle does not affect purity on a stripe screen, that degree of freedom can be used to help get convergence, and the convergence circuits can be eliminated.
Reply With Quote
  #3  
Old 10-22-2007, 04:01 AM
Kiwick's Avatar
Kiwick Kiwick is offline
slave to 3 equines
 
Join Date: Mar 2007
Location: Italy
Posts: 448
Some early 70s 110-degree In-line CRTs like Toshibas, the GTE-Sylvania Uniline, and the Philips 20AX weren't self converging, they still had convergence coils on their necks and required a convergence circuit with lots of adjustment knobs just like delta gun CRTs...

Self converging "Precision in line" tubes (RCA) which were the first to do away with any kind of convergence circuit in the mid-late 70s, had a finer stripe pitch in the center of the screen, and a quite coarse pitch at the sides, unlike earlier inline CRTs which had a constant stripe pitch all over their screen

as for bulb strenght, the real challenge was posed by early 110-degree B/W CRTs, as the flatter bell and increased vacuum would put a lot of strain on the edge of the screen, so early 110-deg tubes were very fragile and dangerous, but by the time the first 110-degree color CRTs came out in the late 60s, the "tensioned rimband" integral implosion protection had already been invented.

In fact, a good CRT (both 90 or 110 degree) with a serious tensioned rimband is extremely safe, and does away with the need for bonded lenses or separate safety glasses... actually, you can't get one to implode even if you smash it with a hammer... it will just break where you hit it and quietly lose the vacuum through the hole.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:03 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.