Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-16-2007, 11:22 PM
kbmuri's Avatar
kbmuri kbmuri is offline
VideoKarma Member
 
Join Date: May 2006
Location: Fort Wayne, IN
Posts: 590
ok, so the 6SN7 swap is really a good idea for this set, but as wa2ise hinted at, the extra stage of amplification just amplified some pretty rotten sound, louder. Hum and tinny, unacceptable.

So I did a complete IF alignment, by the book. With my crude tools, but I'm sure I nailed it. My Knight am signal generator made sine waves, and I set probe A of my tektronix dual-trace scope to monitor them, setting the sweep to 0.1 microseconds/div (or 1 microsecond per full frame of 10 divisions). Counted the waves by hand to make sure the 2nd-hand Knight generator was dead on. 21.25 Mhz where needed, 23.5, 25.3, 22.0. Then I used probe B to measure voltage deflection at test points. Had to build a detector probe per the Sams schematic and a resistor-capacitor filter test point and an insulated tube shield with test-clip loop (for injecting signals inductively into the 1st tuner tube). Quite a time-consuming affair.

Every slug in the sound IF strip was way off base. Every slug responded marvelously, every one is set perfectly now (maximum deflection where called for, minimum deflection where called for, zero-reading where called for). It was really exciting to see everything come into tune, and I was pretty optimistic about the whole process. I even got the languishing .025-volt discriminator output back up to where it belongs. Sure thought it would do the trick.

After removing the filter test point and reassembling channel 13 of the turret tuner and replacing the tube shield, I re-applied VCR signal. Lost all my sound now, and made crap out of my crystal-clear picture.

How exhausting is that?

If this set were my own property, I'm pretty sure I'd part it out now. It got the best of me. Best I think I can do now is take it to a pro, and hope he's not too judgemental of my recap and willing to work on something that's been worked on by an amateur.

Or I suppose I will sleep on it one more time...
Reply With Quote
  #2  
Old 06-17-2007, 03:17 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by kbmuri View Post
So I did a complete IF alignment, by the book. With my crude tools, but I'm sure I nailed it. My Knight am signal generator made sine waves, and I set probe A of my tektronix dual-trace scope to monitor them, setting the sweep to 0.1 microseconds/div (or 1 microsecond per full frame of 10 divisions). Counted the waves by hand to make sure the 2nd-hand Knight generator was dead on. 21.25 Mhz where needed, 23.5, 25.3, 22.0.
Counting waves isn't really that an accurate way to measure frequency. But it does sound like all the circuits fundamentally are working, but at a somewhat wrong frequency.
Quote:
Originally Posted by kbmuri View Post
Then I used probe B to measure voltage deflection at test points. Had to build a detector probe per the Sams schematic and a resistor-capacitor filter test point and an insulated tube shield with test-clip loop (for injecting signals inductively into the 1st tuner tube). Quite a time-consuming affair.
...

After removing the filter test point and reassembling channel 13 of the turret tuner and replacing the tube shield, I re-applied VCR signal. Lost all my sound now, and made crap out of my crystal-clear picture.

How exhausting is that?
Been there at times... VCRs usually create a signal on either channels 3 or 4. I presume you didn't try to use channel 13 (I've made similar silly mistakes myself... :-) )
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:55 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.