![]() |
|
|
|
#1
|
||||
|
||||
|
Found an Emerson 668B at our museum, and for a donation got it. The original 14BP4 has very good emission, and the overall condition is very good. Of course it will be re-capped and cleaned, and aligned if needed. Nice little table model that fits in with the rest of the collection. Info in SAMS 125-6.
Last edited by stromberg67; 05-03-2015 at 04:46 PM. |
|
#2
|
||||
|
||||
|
Very cool ! !
I like Emerson ! Keep posting as you go ... .
__________________
Yes you can call me "Squirrel boy" |
|
#3
|
||||
|
||||
|
Thanks username1. It's going to be interesting. After removing the mouse house, I found that the mouse didn't do too much damage beyond some insulation on one wire, and a peaking coil, 21 ohm, 663 uH. Can't seem to find those, and am wondering if someone could suggest a source. I've already tried Mouser, Digikey, and MCM. Must be a source as the folks doing early color use them.
Anyway, the chassis is in very good condition. Hope to have it up in a couple of months because the summer is looking busy otherwise. Thanks for any suggestions about the coils. Kevin |
|
#4
|
||||
|
||||
|
Usually, peaking coils are a resistor and a coil wired in parallel, they usually wrapped the coil around the resistor. But you don't need to, just use a 22 ohm resistor and a 680uH coil connected in parallel to create a new peaking coil.
__________________
|
|
#5
|
||||
|
||||
|
Well, the re-cap is almost done. and I've found something a "technician" did years ago: installed a 3 amp slo-blo fuse where a .25 amp fast blow belongs, in the horizontal output circuit. No apparent physical damage, and the 6BG6 tests as new. Shorted input cap in power supply, as expected, and all three cans have been re-stuffed. Going to mine a CTC-7 parts chassis for a peaking coil to use until a correct value can be obtained, 620uH to replace a 663uH, with the correct resistor in parallel for now.
Kevin Last edited by stromberg67; 05-17-2015 at 04:29 PM. |
| Audiokarma |
|
#6
|
||||
|
||||
|
Fired up the chassis today and obtained great audio and no smoke. Still need to
replace three caps in the horiz output section that are most likely the cause of the .25 amp fuse blowing. Taking it slow and careful, as some of the components are difficult to get to. Kevin |
|
#7
|
||||
|
||||
|
Well I don't know where you might get a coil if you have already looked at
the usual sources..... Don't forget ebay..... You may just have to re-wind and repair what you have..... But anyway good luck and keep us posted ! .
__________________
Yes you can call me "Squirrel boy" |
|
#8
|
||||
|
||||
|
Depending on the circuit it may not matter what the resistance is, and even if it does if you buy a lower resistance part you could probably add a series resistor to get the same effect as the original.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
|
#9
|
||||
|
||||
|
I got one of these same sets two winters ago. Started on it, but then got distracted with cleaning out my folks house. So I'll enjoy watching you bring your set back to life. It's a nice looking set.
|
|
#10
|
||||
|
||||
|
Nice find Stromberg...they are very rare in Canada.. we can find some plastic Emerson ( end of 80's ) but not like yours..
|
| Audiokarma |
|
#11
|
||||
|
||||
|
Thanks for the nice comments all.
Saturday night I poured myself a nice big cold drink, and connected three meters to the main power supply points, turned the TV on, and sat back and watched for a while. As expected, the pic started to bend at the left top after about a half hour. The meter readings were strange. I started to adjust the various user controls, and found a "sweet spot" with the contrast control where all voltages became "normal", and a decent pic was obtained. Suspecting the 6AC7 video output is gassy, or maybe some other defect. All caps replaced, and out of spec resistors also. Many resistors were well within spec, which I found strange but gratifying. I'll pull out another 6AC7 from stock and see what happens. Maybe I should stick to RCA's . Kevin
__________________
stromberg6 |
![]() |
|
|