![]() |
|
|
|
#1
|
|||
|
|||
|
zenith 20bc50 problems
i have a 20bc50 chassis zenith i use as my everyday tv i did a semi full recap ( didn't do lytic cans) when i got it about 2 years ago. its been working well since i started using it daily about 7 weeks ago. last night we were watching tv and it had been on maybe 4 hours and suddenly the vertical went jittery, its not interlacing correctly and its stretching the picture.
i have done nothing recently to the set except perform a full setup. i currently have no pictures of it showing the problem but i will soon ( i have no internet at home) i do have pics of the tv from when i first got it and recapped it just to add some eye candy http://i159.photobucket.com/albums/t...v/DSC05978.jpg http://i159.photobucket.com/albums/t...v/DSC05953.jpg http://i159.photobucket.com/albums/t...v/DSC05956.jpg |
|
#2
|
|||
|
|||
|
I would look at the electrolytic that is attached to the cathode of the vert out.
may be shorting out. |
|
#3
|
|||
|
|||
|
I have one of those sitting right here next to me that working perfect. All origonal not one part replaced.
If you need any info or me to check anything like voltages on it let me know. Could be anything in the vert circuit from a bad pot to a small value cap. I think they use a VDR too that can cause issues. I would have to look at the schematic. |
|
#4
|
|||
|
|||
|
well i took it apart checked everything redid all of my solder work and cleaned the controls. it worked for a few minutes and started again then started making a weird buzzy hum and vertical would collapse and pop back. now all i can get is 3 very badly converged horizontal lines
|
|
#5
|
|||
|
|||
|
Try a new tube first then if that doesnt work start checking dc voltages. Do you have the schematic for it?
|
| Audiokarma |
|
#6
|
|||
|
|||
|
i do not have the schematic also dont have another tube but ill try and get one next chance i can.
heres a pic of what its doing now http://i159.photobucket.com/albums/t...7/DSC02317.jpg |
|
#7
|
|||
|
|||
|
...
Last edited by andy; 12-05-2021 at 09:05 PM. |
|
#8
|
|||
|
|||
|
ended up buying the sams found that the scan is so horrible i might as well have just not gotten it at all. if anyone has the original im trying to find the value of R138 . the sams is set 1197 folder 2 if anyone can help id appreciate it.
|
|
#9
|
|||
|
|||
|
Sams 1197 folder 2 shows R138 as 470ohm 2W.
|
|
#10
|
|||
|
|||
|
From looking at the schematic the 30mf and 40mf caps connect + to + with one end of R136 and one end of R138. The other end of R138 goes to the 390v B source. This source is from The vert centering control.
|
| Audiokarma |
|
#11
|
|||
|
|||
|
I can scan the schematic and email it to you if you like just pm me.
|
|
#12
|
|||
|
|||
|
well replaced the resistor blew again checked all my capacitor hookups everything was fine. traced out everything and i think there's something wrong with my focus section. this kinda makes sense before the set died the focus would be out for the first 5 minutes the set was on, and would swing in and out while playing. i just figured it was moisture or something as it would crackle and hiss for that first few minutes and would stop after the focus had come back. point is there anything known for going bad in the focus sections on these televisions and would the focus affect the hv at all? since that seems to be working.
|
|
#13
|
|||
|
|||
|
carbon deposits for HV arcing in the HV rectifier socket, and around the flyback area could cause this. Probably low high voltage causing lack of focus while it was crackleing and hissing. Also check around the damper tube socket. The damper tube plate does tie back to the 390v (b) source. I doubt the focus problem caused the burnt resistor. Check the windings of the vertical output transformer and componants in the vertical output circuit, including the 6JC5 tube and socket.
|
|
#14
|
|||
|
|||
|
spent last hour checking everything i could i cant find my good multimeter to save my life and the backup isn't exactly up to my needs. i pulled the hv rect. took 20 minutes as it seemed glued in finally popped out taking part of the fly back board with it :/ socket is immaculate far as i can see. only sign of arcing is on a resistor that ties to the focus voltage feed to the crt. the resistor is nowhere on my schematic ( original zenith) or the one i recieved from bill (sams) though. i checked the vertical output xfrmr as far as i can tell everything seems fine. i have neither a tester or a spare tube for the 6jc5 though i can say like every tube in this set its original. not that that means much.
![]() ![]()
|
|
#15
|
|||
|
|||
|
Take those two philips screws out and look on the back side of that tube socket. That is where arcing usually happens.
|
| Audiokarma |
![]() |
|
|