Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-25-2008, 09:52 PM
AndyMack's Avatar
AndyMack AndyMack is offline
VideoKarma Member
 
Join Date: Dec 2007
Location: Albany, NY
Posts: 50
Chromacolor II blooming issue

Ok... I've got two sets down right now (other is a roundie), trying to get the easier of the two fixed.

It's one of the Zenith Avanti series, circa 1974 (?), white with the rosewood top, not a remote set. This TV has the following numbers on the sticker on the back cover, Model E4760, chassis 25EC58 (it's really faded, best I could make out). The chassis itself says 25EC83, looks original but who knows. This set was a one-owner, who claimed it was a good TV that only required a new CRT sometime in the late 80's.

Works well but the picture has a blooming issue, where the image gets larger with increased brightness, seems to go out of focus a little and whites will smear when the contrast is turned up to what would otherwise be a normal level.

I'm not very educated when it comes to TV repair, so I thought I'd pose the question here. Is this a simple module(s) replacement, or do I have to dig into the circuitry to fix this problem.

This set also has a noisy transformer (you can hear it hum when the room is quiet). Related or no big deal?

I love this TV, has great color and a sharp picture when bright/contrast is turned way down. Any advice is appreciated as always!
Reply With Quote
  #2  
Old 08-25-2008, 11:18 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Flip the service switch on the rear of the chassis to the set-up position. There should be a line across the center of the screen. If it is very bright, try turning down the red, blue, and green screen (G2) controls. These controls should be adjusted for a barely visible white line.

Also, check the 240 volts going to the CRT screen constrols. You can check this voltage at C270, a 10 mfd, 300 volt electrolytic cap. This cap is located under the chassis and should be close to the flyback side of the chassis.

BTW, that chassis is from '74 is was probably the best color chassis that Zenith made. What brand of CRT is in there?
Reply With Quote
  #3  
Old 08-26-2008, 09:42 AM
jpdylon's Avatar
jpdylon jpdylon is offline
<-- sucker for old sets.
 
Join Date: Apr 2005
Location: Knox County, Tennessee
Posts: 1,675
Also check to see that the 24v regulated power supply is working properly and putting out a clean 24v DC under all picture conditions. Its normal for the picture to bloowm a little on high contrast scenes of the control is turned up a bit.

I believe 74 was the year before they started using the white HV regulator cap of death, but you might pull the back and check under the HO transistor heatsink. If you see a white 4 lead capacitor in there, stop using it until you replace it.
__________________
Jordan
Reply With Quote
  #4  
Old 08-26-2008, 11:05 AM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
I think that chassis uses several white HV caps connected from the collector of the horizontal output transistor to ground. It would probably be a good idea to replace these with modern capacitors of the same rating.
Reply With Quote
  #5  
Old 08-26-2008, 12:00 PM
kx250rider's Avatar
kx250rider kx250rider is offline
REAL TVs have TUBES!
 
Join Date: Oct 2005
Location: Los Angeles & Dallas
Posts: 3,239
Quote:
Originally Posted by radiotvnut View Post
I think that chassis uses several white HV caps connected from the collector of the horizontal output transistor to ground. It would probably be a good idea to replace these with modern capacitors of the same rating.

YES!!! That chassis has (5) safety caps, Zenith part 22-5001. I think 3 of them are on the phenolic board on the flyback, and the others are below the chassis. If yours has white ceramic ones, they were recalled in the late 70s by Zenith and you must replace them to prevent the high voltage from escalating and possibly breaking the glass neck of the picture tube. In addition to CRT drive voltage problems (as discussed in some of the other answers) blooming is a symptom of too much high voltage, or poor regulation.

Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10
Reply With Quote
Audiokarma
  #6  
Old 08-26-2008, 12:53 PM
AndyMack's Avatar
AndyMack AndyMack is offline
VideoKarma Member
 
Join Date: Dec 2007
Location: Albany, NY
Posts: 50
Wow. Good things to know! I will check for everything listed here after I get home from work tonight. Thanks!
Reply With Quote
  #7  
Old 09-02-2008, 09:56 PM
AndyMack's Avatar
AndyMack AndyMack is offline
VideoKarma Member
 
Join Date: Dec 2007
Location: Albany, NY
Posts: 50
Ok.. wanted to just check back and provide a couple of photos:

The chassis is in fact a 25EC58, don't know where the heck I got the other number (might be off my other Zenith).

Looked at the HV section - there appears to be something that has been removed. In the photo, just to the left of the tripler. Any ideas what that was?

Tube looks original. A photo of the sticker on the tube is provided, but I dont know how to decipher the numbers.

Will pull the chassis this week and check for the white caps. I've been hammered with unexpected overtime at work this last week, so haven't had a chance to really sit down with this set like I've wanted. Please bear with me.

Last edited by AndyMack; 03-21-2009 at 10:40 PM.
Reply With Quote
  #8  
Old 09-02-2008, 11:55 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Quote:
Originally Posted by AndyMack View Post
Ok.. wanted to just check back and provide a couple of photos:

The chassis is in fact a 25EC58, don't know where the heck I got the other number (might be off my other Zenith).

Looked at the HV section - there appears to be something that has been removed. In the photo, just to the left of the tripler. Any ideas what that was?

Tube looks original. A photo of the sticker on the tube is provided, but I dont know how to decipher the numbers.

Will pull the chassis this week and check for the white caps. I've been hammered with unexpected overtime at work this last week, so haven't had a chance to really sit down with this set like I've wanted. Please bear with me.
Oh yes, before you pull the chassis, see if that TV has a removable metal plate on the underside of the cabinet. Most Zenith's with the horizontal chassis had this feature so that the underside of the chassis could be serviced without removing the chassis. If you have to remove the chassis, make note of where each plug goes.
Reply With Quote
  #9  
Old 09-02-2008, 10:44 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Some of those early solid state Zenith's had a seperate tripler and focus divider resistor. Often, one or the other would go bad and the technician would use the newer style (ECG523, 526, etc) tripler with the built in focus divider. I suspect that to be the case here.

I know how it is to get caught up in other duties; so, take your time. Lord willing, we'll be here when you get a chance to get back on it. I've got unfinished projects that have been sitting here for 15 years. I need to stop bringing home more stuff and fix what I have.
Reply With Quote
  #10  
Old 09-02-2008, 11:50 PM
zenith2134's Avatar
zenith2134 zenith2134 is offline
VideoKarma Member
 
Join Date: Feb 2005
Location: UTC -4
Posts: 2,546
Nice set, Andymack! I'm not sure about your chassis, but it looks like a keeper for sure. Those had some very nice pictures on em.

I have unfinished projects invading my garage. A lot of them, in fact.
Reply With Quote
Audiokarma
  #11  
Old 12-16-2008, 09:33 AM
AndyMack's Avatar
AndyMack AndyMack is offline
VideoKarma Member
 
Join Date: Dec 2007
Location: Albany, NY
Posts: 50
Finally got around to changing out those safety caps. I used what was quickly available - that being some Panasonic .0018uf @ 1.6kv metal-poly caps.

I posted a video on YouTube of this set in action. One thing that sticks out is the presence of what sounds like flyback whine - which is only heard in the video, you can't hear it standing there watching the set. Not sure why the camera hears it, but not my ears. The set does hum a little, sounds like 60 cycle hum, but it's only noticeable if the room is quiet.

Anyways, here's the link: http://www.youtube.com/watch?v=stTdAggtlZg

Thanks to all for your advice!
Reply With Quote
  #12  
Old 12-16-2008, 12:59 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
The soft focus could be caused by a failing HV tripler. I've fixed many Zenith's of this vintage that either had marginal focus or the focus was optimum at the extreme end of the focus control range by replacing the tripler. Before you change the tripler, examine the CRT socket for corrosion around the focus pin.
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:32 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.