|
The best I can do is a hi-res photo of the chassis schematic, very little online on the Magnavox sets of this era, I don't know where my notes & schematic of the op-amp video interface are so I'm working from memory on this one, they're around here... somewhere.
Okay so this afternoon I went for broke and literally jammed the output lead of my video op-amp into pin-2 of the 6MU8 video out tube without making any other changes to the IF or the video detector side of the board, hit it with some color bars and the most "watchable" picture appeared on the screen. Going this way to me seemed like the most logical in terms of maintaining the DC loop thru the sound trap despite the impedance mismatch so maybe this is something you might want to consider with your Zenith.
I couldn't find a free online schematic of your EC chassis so I'm no able to follow along, if you know of one point me in the direction and I will take a good look at it.
So the op-amp circuit I'm working with is a simple non-inverting layout using an Analog Devices LT1252 in the 8-pin DIP package. Input is direct coupled and the gain is set to 8V P-P output which is then fed to a 100 ohm pot to adjust the final output level, I'm using the suggested layout of the datasheet and it's powered by a regulated and well filtered +/-9V onboard linear supply. The input signal is also directly coupled to an LM1881 8-pin DIP sync separator which can supply raw vertical, horizontal and composite sync plus a burst/back porch and odd/even output, early on I was using the v-sync to drive the vertical section directly and H-sync to the AFC diodes thru an NPN as an inverter. In this arrangement raster lock was absolute and the horizontal would remain locked thru the entire range of the control pot. The big downside to all of this was an uphill battle with DC restoration and this appears to be far more stable now using the brute force video injection to pin-2 (grid-1) of the 6MU8, schematic of the video amp below.
Now I'm waiting on a fresh 6MU8 to arrive tomorrow, want to make all the adjustments using a known good tube.
schematic of the video amp used in the Mag T-940. Flag 56 feeds the input of the 6GH8 sync sep and between R726 & R727 is the feed to the AGC grid-1. Plate section of the triode goes thru a parasitic suppressor then the delay line while the grid gets a blanking pulse from the vertical. Flag 22 goes thru a 22k resistor then to the low side of the brightness control which has the high side on a divider and +140V. For some reason imgur is not allowing me to post more images so I can't include the wider view.
Okay an addendum to all of this.
I have finally integrated my video/sync buffer amp into my Magnavox with excellent results, most of the work was housekeeping and finding the most suitable places to inject the signals and at 03:30CDT this morning everything came to life. I ended up connecting a shielded wire directly to Pin-2 of the 6MU8 1st & 2nd video amp tube leaving the entire video detector circuit intact and removing the 3rd IF coil connection from the plate of the 3rd video IF tube, from there it was run a pair of shielded wires from the buffer amp vertical pulse output to feed the vertical osc which was isolated from the sync separator by lifting one side of R-515. Horizontal is still keyed off the sync separator which has now become essentially an amplifier to feed the needed 35V P-P to the AFC diodes, one side of R-725 was lifted to inject the composite sync out of the buffer amp. The reason for this is twofold; one I can now use sources with non-standard sync levels to maintain a raster lock and two maintaining the sync separator maintains the original timing of the horizontal to the burst gate. I'm using the Texas Instruments LM-1881 video sync separator chip for the timing as they're very simple to use and have plenty of drive, the composite sync feeds a 2SC945 which is emitter coupled to the 6GH8 sync separator via C-724.
The biggest problem I'm having is uploading images to the videokarma server and as a result they are not available for this post. If you want to see the images you will have to send me a private message with your email or other means of file transfer as downsizing them to fit the antiquated requirements cuts too much of the details out and is completely unacceptable in this day when the minimum image from a typical phone camera is several megabytes in size with little one can do to reduce this.
The alternative is to follow along on another site where I have also posted my progress on this and many other projects over the years on my dedicated thread called "On The Bench" that is found in the Ham Amateur Radio section of smokstak.com and my username there is Brhatweed.
Last edited by ARC Tech-109; 05-05-2026 at 04:06 AM.
Reason: To add more information for those who care.
|