My first major overhaul
 

Greetings all :)

Im new here and also apreciate old B/W tv sets, been tinkering with em since the 6th grade. Got out of it for awhile, but am back to it. :)

Recently, i scored a Packard Bell 2116 DeLuxe (2115-2 chassis) Iknow i need to do a total Cap job on it. UNFORTUNATELY, the owner didnt know that and PLUGGED IT IN... Needless to say , he smoked the transformer (stamped 89041) Looks like a 13 wire one, (primaries included in count)

Fortunately, i kept a BIG box of tubes so thats covered, only wish i wasnt forced out of the garage or ide still have my old tv parts around...

Ide apreciate any help (parts, spec books, advice, etc.) you can give me :)
check your piles :) :)
Thanks
Steve

Welcome! I would think among the group here we can at least find you a Sams schematic package for this set. Are you certain the transformer is shot? I am not at all familiar with Packard-Bell sets as few of them seemed to come this far east.

thanks Bgadow :)

Yeah im afraid its shot, the guy admitted to plugging it in and he saw smoke from the transformer (he didnt know better) It also has that sweet aroma you get from burnt windings.. The tv looks comparable to a DUMONT chassis.

Im hoping more collectors will chime in with parts and some help with this project. The cabinet is SWEET and ide love to get this back up and running

This isnt the first packard bell ive had, i had a tv/radio/phonagraph combo in 79. Had the parts lying around till about 2 yrs ago when my nephew cleaned the garrage out and errected a bedroom. I lost alot of good parts that day, so im starting from scratch on this project.

Again thanks for the fond welcome :)

Steve

You may find a transformer at Moyers Electronics. They supplied one for my RCA TC-127 restoration when I thought there was no hope.

http://www.moyerelectronics.com

thanks tubejunke :)

I just left them a parts inquiry

Steve

Welcome to th' Mad Monks section of AK...Here you will find no end of arcane knowlege, half-forgotten lore, & hopefully a tranny for yer Studebaker-Packard, erm, Taco Bell, uhh, PACKARD-BELL...Hey, I knew I'd get it right...

Here is some info I dug up: the set is listed in Sams 195-9. I have a copy that I'll send you-shoot me a PM with your address and I'll stick it in the mail. Some versions of your set used transformer # 89036B. Looks like either version will work with minor changes. Stancor part # is P-8340, Thordarson is 26R35.

thanks Sandy G and all others whove chimed in and offered help
Its TRULY appreciated, I admit i was worried at first about being able to restore this tv, but after all the replies, i'm feeling alot better about it

This is truly an "AWESOME" place :)
Thanks again all :)
Steve

Looks like Moyer cant find me a power supply but they do have the flyback...

Not sure if the CRT is good, according to my tester its weak, then again i dunno if my tester is accurate :)

Either way this is what the project looks like

Steve

what about a T639?

>what about a T639?

What are the output specs on the T639 fujifronitier?

Hunting for caps.
 

Okay, the parts are on their way..

where does one find capacitors? My MOUSER book is an 04 and its quite confusing dont see any 600v ones in there.

Also have 3 can caps that need to go. Where does one find all the caps they need? :scratch2:

Steve

Here are a couple of sources for capacitors.

http://www.tubesandmore.com/

http://www.radiodaze.com/

There are more . . .

It may be tricky to find an exact replacement for a multi-unit can capacitor. Most people either disconnect the old cans and wire new caps under the chassis, or "restuff" the old cans with new caps.

Regards,

Phil Nelson
Phil's Old Radios
http://antiqueradio.org/index.html

We have found some good deals recently on 450 v. electrolytics at Mouser (individual value caps, you can use a terminal strip to mount them on and replace the cans)
Just search at http://www.mouser.com rather than using the paper catalog.
Am not sure if they have 600v mylar caps as we have not had to re-stock those yet but we have found Mouser gives the quickest service and a true wholesale price on what we have ordered from them.

Thanks for the wonderful cap hookups :)
I dont know if its just a "packard bell thing" Having trouble locating replacements for the wax caps with .MFD@600V types EX. .1, .05, etc.

Can anybody link me in the right direction?
Thanks
Steve