#16
|
||||
|
||||
You can also try adjusting the center frequency, as long as that doesn't clip off one end or the other (left or right) of the waveform.
|
#17
|
|||
|
|||
Continued 41.25 Trap Alignment:
Last edited by bhegges; 12-02-2023 at 10:29 PM. |
#18
|
|||
|
|||
L1, L2, L3 alignment:
The direction call to adjust for minimum response as you adjust each coil and there may be some interaction, I was not sure on how to do this as it relates to the scope response, I just tried to get the response cure to match the picture, zooming in on the scope was some help. SAMS directs making these adjustments and using a VTVM to indicate. I tried this too but not easy to adjust to the minimum, note I cheated and used test point C2 (accessible on the chassis) which is in front of R49, 330 ohm, where SAMS has test point E on pin 7 of the sound & sync amp tube. Adjustment to L1, L2, and L3 got tricky real quick and trying to keep track of the adjustments in case I need to go back went out the window. I did find adjustments in the subsequent step helps with getting a matching response curve. I likely will repeat all of these steps as I zero in on the alignment. Starting point with the same 7 markers turned on as indicated in Fig 12, note Zenith uses a 41.75 while the B&K 415 has a 41.67, close enough Last edited by bhegges; 12-03-2023 at 12:28 PM. |
#19
|
|||
|
|||
Tuner converter plate coil & IF Transformers T1, T2, T3 alignment:
I will follow up with some pics of where I land for the final IF & Trap alignment. |
#20
|
||||
|
||||
Quote:
2) What do you mean by "fall in the correct place?" If the procedure says min or max at the marker, it means only that - the vertical position of the marker should be min or max. If the curve ends up looking wrong *at the end after all adjustments have been made*, there is something wrong with your setup or you made a mistake earlier in the procedure. It is possible the curve won't look right when you are only part way done. |
Audiokarma |
#21
|
|||
|
|||
The 75 ohms is the setting on the B&K 415 Signal cable, you can select 75 or 300
"fall in the correct place?" maybe not the best way to describe but as I adjust a coil the response curve on the scope moves right or left which has the effect of moving the marker up or down
I agree on needing to bring it all together, I will follow up with where I am at in a bit. Last edited by bhegges; 12-09-2023 at 05:03 PM. |
#22
|
|||
|
|||
OK here is where I am at:
Scope measuring on test point C1, all 7 markers are turned on, note the B&K 415 has a 41.67 marker vs a 41.75 marker which is what Zenith references. Directions are to make adjustments to the 41.25, 47.25, and 39.75 traps (L1, L2, L3) for minimum responses, accuracy of trap attenuation and marker locations. Scope measuring on test point C2, same 7 markers are turned on. Goal is to make adjustments to the converter plate coil and 1st IF coil (T1) to match the response and also to adjust the 2nd and 3rd IF coils (T2, T3) for maximum response and to approximate the response curve. |
#23
|
||||
|
||||
Quote:
|
#24
|
||||
|
||||
The spec for 41.25 attenuation at C1 is 24 dB or greater, which means it's Ok if it's higher on the scope (closer to the top, which equals zero signal) than shown in the illustration.
At C2: a 1 dB reduction in signal from the peak is the same as a 20% [correction - 10%] reduction. So the distance shown as 1 dB in the illustration should be 20% [correction - 10%] of the max height. (the sketch looks poorly drawn - more like 10%.) [Correction - the sketch looks correct]You are getting over 30% attenuation at the markers, so this indicates the curve is too narrow. Last edited by old_tv_nut; 12-09-2023 at 08:27 PM. |
#25
|
||||
|
||||
Please see correction to previous post - 1 dB should have been 10%, not 20%
|
Audiokarma |
#26
|
|||
|
|||
Quote:
|
#27
|
|||
|
|||
I have tried to get the 43 to 44 mc at 1db (10%) of the 42.75 and 45 mc markers. I got it down to 20% but this comes at a cost of moving other markers out of proportion. Thoughts on which markers are most important to have correct? Note currently I am trying to get the curve shape to match and to keep the 42.75 and 45 mc parallel.
|
#28
|
||||
|
||||
Curious that the drawings show 42.75 and 45 equal for both test points, but your measurements don't. Not sure what to think about that.
|
#29
|
||||
|
||||
OK, I went back through the whole thread from the beginning, and I see you are not using the RC network from figure 6, and have the sweep generator output termination set to 75 ohms.
Try this - keep the sweep generator output termination set to 75 ohms, but add onto it the RC network from Figure 6. My guess is that the 75 ohm impedance is loading whatever grid circuit you connect to and that is causing the incorrect responses. |
#30
|
||||
|
||||
I think I read too fast earlier and mistook the RC network in figure 6 for an external marker adding arrangement - apologies!
|
Audiokarma |
Thread Tools | |
Display Modes | |
|
|