#31
|
||||
|
||||
You SO make me want to take on my 5317U again, but I have several things ahead of it.
|
#32
|
|||
|
|||
The dial bulb might be easier to access from the front of the set, by removing the knob.
|
#33
|
||||
|
||||
I tried that but didn't see any obvious way to get the bulb
|
#34
|
||||
|
||||
The socket might be on a slide on-off mounting.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#35
|
|||
|
|||
You might want to simply pull the VHF tuner. Zeniths (at least the B&W ones) had the VHF tuner mounted with two screws in the cabinet back. I see what looks like rubber grommets on the side of the VHF tuner mounting bracket interfacing with pins on the front face plate.
|
Audiokarma |
#36
|
||||
|
||||
I tried getting at it from the front and the knob came apart
I think the smoked plastic goes towards then then white paper then the clear plastic then the black ring After a bit of poking around, I realized the bulb holder slid off pretty easily. The holder clip is the ground and the wire clips onto the tuner. It appears to be a #240 bulb - 6.3V @ 0.36A. Specs: http://www.taillightking.com/images/...0240%20USA.pdf All I had handy was some #1847 (long life #47) and an LED equivalent. They only draw 0.15A and I expect are not as bright. It works but is really dim. |
#37
|
||||
|
||||
#38
|
||||
|
||||
Be careful with that knob - that pot metal "cage" liked to break. I broke the one on our neighbors' Mother-in-Laws set....
https://flic.kr/p/Td3QqK Cheers,
__________________
Brian USN RET (Avionics / Cal) CET- Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
#39
|
||||
|
||||
Quote:
__________________
Just look at those channels whiz on by. - Fred Sanford |
#40
|
||||
|
||||
Thanks for the info
I hooked the set up to a converter box and watched a little MeTV tonight. Definitely an improvment over the weak OTA reception! There vertical height is a little lacking and horizontal hold is at one extreme. Also some streaking when text appears. It ill be interesting to see how things change after a recap and weak tubes are replaced. Last edited by bandersen; 03-30-2017 at 10:52 PM. |
Audiokarma |
#41
|
||||
|
||||
Tip on the horizontal hold: the control is a coil, not a pot....So the stop is the knob's pointer hitting the metal tab in the pencil box. To get more range pull the knob out past the point where the pointer hits the stop then turn it some more. The knob should have a hex shaft so you could set it up so the pointer is at mid mech range at the center of the electrical sync range. I can't remember changing caps having much effect on H hold range in Zeniths.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
#42
|
|||
|
|||
biggest issue with Zeniths was the coil forms, the plastic is an issue, other than that they pretty much just work, even with the old caps. Sometimes you may find a cold solder joint on a tube socket, IIRC the video out on later models had this issue, maybe not a prob on the roundies, but it would manifest as a overly bright pic esp near the bottom, solved with a smack of the cabinet. A good socket cleaning of all the tubes will get you 90% of the reliability back, and that's assuming it was stored where corrosion could take hold. Zeniths were built to last, the other plus is the HV was very robust with no flyback issues.
|
#43
|
||||
|
||||
Quote:
__________________
Just look at those channels whiz on by. - Fred Sanford |
#44
|
|||
|
|||
Yea the RCA PCB's on high hour sets are frequently smoked.
|
#45
|
||||
|
||||
Unfortunately that was also true of clone sets by Philco sylvania magnavox GE Emerson etc. no wonder zenith got such a jump on everyone else🙂
__________________
"When resistors increase in value, they're worthless" -Dave G |
Audiokarma |
|
|