Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Vintage TV & Radio Tech Forum

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-16-2018, 10:30 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
1981 Zenith System 3 problems

I picked up this set from a closed down repair shop around Christmas,It sat on display in the front window since I believe 1989,in the sun,under a leak,yeah.... It works great aside from some minor gripes,it won't shut off,and with an amplified signal fed straight to it it's still a little grainy,like a good over the air signal almost. I know of the triac in the remote power supply that likes to short and that's the issue here,but where on earth do I find a replacement? None of the numbers on it cross reference. I've gone through this thing and cleaned the grounds and I'm wondering if I need to just take the plunge and recap it. It's a 9-160 set.
Attached Images
File Type: jpg IMG_20171207_195716122.jpg (61.5 KB, 51 views)
Reply With Quote
  #2  
Old 01-16-2018, 11:29 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
Here's some more pictures
Attached Images
File Type: jpg IMG_20171217_130831588_HDR.jpg (72.4 KB, 55 views)
File Type: jpg IMG_20171209_143056035.jpg (76.1 KB, 49 views)
File Type: jpg IMG_20171209_142804099.jpg (91.9 KB, 43 views)
File Type: jpg IMG_20171209_142748741.jpg (88.8 KB, 55 views)
Reply With Quote
  #3  
Old 01-17-2018, 08:41 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,672
I would try a triac from earlier CC2 chassis its probably the same.
Seen NOS triacs on e-bay. They get subbed to a kit 800-###, I
dont remember all the number.
I wouldnt recap unless a problem. There is a 10mfd 315V on the
back edge by the FBT that always goes. I would remove the 9-160
& go over it for cold joints, there ARE some !
For the RF check the ant cable. Also the tuner plugs get cold joints.
On the IF board 9-151-# ? there is an AGC delay control.
Last check the CRT socket 9-155-01 for cold joints especially under
the white resistor pack & socket itself.

73 Zeno
LFOD !
Reply With Quote
  #4  
Old 01-19-2018, 09:58 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
I forgot to mention I cleaned up all the contacts in there as well. The antenna cable is in great shape. Next time I have the bench space I'll tear it down and go over everything for cold joints. Ok,AGC delay control,what is it's function and how can I adjust it properly? I have experience on electronics but I'm still learning,especially on TV's.

I see a Zenith Triac replacement kit on eBay part no. 800-618. It just looks like a cable in the bag, is there something I'm not getting about the replacement?

Last edited by Laserdisc; 01-19-2018 at 10:44 PM. Reason: omitted info
Reply With Quote
  #5  
Old 01-20-2018, 09:13 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,672
The cable plugs in series with the power wires ( black, blue, grey )
on older CC2 sets & has a VDR added. Should also have instructions
& triac & IIRC hardware, mica etc. Remember I am ASSUMING the
triac is the same !!!!!

RF AGC with strong signal turn untill snowy. Turn back until
it just clears up & leave it there.

73 Zeno
LFOD !
Reply With Quote
Audiokarma
  #6  
Old 01-20-2018, 02:13 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
I ended up getting an nos remote module off eBay so we'll see what that does for it, right number and everything.
Reply With Quote
  #7  
Old 01-20-2018, 03:41 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,672
Quote:
Originally Posted by Laserdisc View Post
I ended up getting an nos remote module off eBay so we'll see what that does for it, right number and everything.
I like it ! Fast & easy. We only used the kits on the old sets that had a
massive tuner assy that cost like $80 exchange rebuilt. Come to think
of it I dont remember changing any of the small on/off modules !

73 Zeno
LFOD !
Reply With Quote
  #8  
Old 01-20-2018, 06:14 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
I usually like to troubleshoot and buy component parts but the right module nos for $10 seemed too good to pass up. I've also ordered that cap so when everything comes in it'll get blown apart and get some much needed TLC.
Reply With Quote
  #9  
Old 01-31-2018, 12:32 AM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
Well, wrong part number. Crap. Visually identical module but the number is different. Installed the set won't turn on,so back to the original for the time being until I can find a triac.
Reply With Quote
  #10  
Old 01-31-2018, 12:12 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 14,758
There is a module cross reference manual IIRC the CRSP that tells what will interchange. Someone posted it on vk.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Audiokarma
  #11  
Old 03-02-2018, 09:53 AM
dtryon dtryon is offline
VideoKarma Member
 
Join Date: Jan 2018
Posts: 37
Triac for Zenith

Laserdisc,

Here is a link to a Triac's that will work great in your Zenith. I was a repair tech working on Zeniths for years and the Triac you want to replace is a very generic part,. Hope this helps: https://www.ebay.com/itm/10PCS-BTA16...4AAOSw32lYroTn Or cross this number to a NTE number.

Dennis
Reply With Quote
  #12  
Old 03-12-2018, 12:25 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
Hey,for 10 for $3.50 I'll give it a shot. Mine has a blue GE branded one that didn't cross reference to anything so I couldn't find anything. One issue with the tv that I've neglected to mention here is that with a weak signal it has some light retrace lines and when showing a solid black screen with a good signal there are a couple of vertical lines in the middle of the screen, it looks like maybe a degaussing is in order if I can find a coil but the grainy picture and retrace lines concern me. Both are very minor and have not worsened with lots of use but I like this set alot for some reason and I want to fix any issues it has.
Reply With Quote
  #13  
Old 03-13-2018, 08:17 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,672
Change the 10mfd 315V cap near the FBT. Causes any of the following.

cant turn down brite
retrace lines
jail bars
pix dark to light across screen
smearing, streaking
" just not right" pix.

VERY common on ANY SS color TV. Can fool some into thinking CRT bad.

73 Zeno
LFOD !
Reply With Quote
  #14  
Old 03-13-2018, 10:16 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
Strange that one cap can cause all of that,but that sounds exactly like the problems I'm having. I'll replace it and see how well it wakes up. Now that you mentioned the brightness part turning "picture" all the way down doesn't completely blank the screen like every other tv I have.
Reply With Quote
  #15  
Old 03-17-2018, 09:00 PM
Laserdisc's Avatar
Laserdisc Laserdisc is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Chattanooga
Posts: 53
That cap certainly improved matters! Cleaner picture,no retrace lines,brightness is now the expected linearity instead of a crap shoot,cool! The vertical lines are still there on a black screen but considering this thing sat in a window for almost 30 years in direct sunlight under a huge leak I suppose I should be happy the thing works right at all. Speaking of,when I had the 9-160 out to replace the cap I got a better look at the total damage,starting to get some board rot along the edge near the CRT,few more years under that leak probably would have finished it off but If taken care of should last a good long while.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:24 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.